XT60 Male Connector with 14AWG High Temp Silicone Wire Pigtail - 10cm

Specifications

• Connector Type: XT60 Male (Plug)

• Wire Gauge: 14AWG (American Wire Gauge)

• Wire Length: 10 cm (Excluding connector)

• Insulation Material: High-Temperature Soft Silicone

• Conductor Material: Tinned Copper (High conductivity, corrosion resistant)

• Rated Current (Instant): ~60 Amps

• Temperature Resistance: -60°C to +200°C

• End Termination: Pre-tinned bare wire ends (Ready to solder)

Key Applications & Projects

• Drone Builds: Perfect for connecting Power Distribution Boards (PDB) or 4-in-1 ESCs to the main battery.

• LiPo Battery Repair: Replace damaged connectors on 3S/4S LiPo batteries.

• General Robotics: High-current power lines for combat robots or rovers using 12V-24V systems.

 Unlock New Capabilities (Project Evolution)

• Prerequisites: If you have been using JST or DC Barrel jacks, you are limited to ~3-5 Amps.

• Feature Upgrade: Switching to this XT60 system unlocks the ability to drive high-power BLDC motors and heavy-duty actuators, handling bursts up to 60A without voltage sag or connector melting.

• Effort Level: Beginner. Requires basic soldering to attach the bare wire ends to your device.

Virtual Technician & Wiring

• ⚠️ Polarity Warning: Always verify polarity before connecting to a battery. Standard convention:

  • Square Edge / Red Wire: Positive (+)

  • Chamfered Edge / Black Wire: Negative (-)

• Probots™ Secure-Transit: Shipped in anti-static or sealed packaging to prevent copper oxidation and keep the connector contacts pristine during transport.

Accessories & Parts

What's Included:

• 1 x XT60 Male Connector with 10cm 14AWG Silicone Wire (Pre-soldered)

Required Alternatives (Not Included):

• Soldering Gear: A 60W+ Soldering Iron is recommended for 14AWG wire work.

• Insulation: 4mm or 5mm Heat Shrink Tubing (to cover your board-side connections).

Compatible Upgrades:

• Mating Connector: XT60 Female Pigtail (for the battery side).

• Protection: LiPo Battery Voltage Checker/Alarm.

Frequently Asked Questions (FAQ)

1. Is this the Male or Female side? This is the Male connector (pins are visible inside the housing), typically used on the "Load" side (ESC/Drone), while the Female is used on the Battery.

2. Can this handle a 6S LiPo battery? Yes, the voltage rating of the wire and connector easily supports 6S (22.2V) and even higher.

3. What is the exact length of the wire? The wire length is 10cm (approx 4 inches).

4. Is the wire made of copper or aluminum? It is Tinned Copper, which is superior for soldering and conductivity compared to aluminum.

5. Can I use this for 3D printer heated beds? Yes, XT60 is excellent for 3D printer high-current heating elements.

6. Does 14AWG wire handle 60 Amps continuously? 14AWG is generally rated for 45-50A bursts in open air. For continuous 60A loads, we recommend stepping up to 12AWG, though this is sufficient for most drone bursts.

7. Is the wire insulation heat resistant? Yes, it is silicone insulation, heat resistant up to 200°C.

8. Are the wire ends pre-tinned? Yes, the exposed ends are pre-tinned for easier soldering to your PCB.

9. Will this fit an XT60H connector? Yes, XT60 and XT60H are compatible; the 'H' just includes a sheath cover.

10. Can I use this to charge a lead-acid battery? Yes, as long as the current matches the rating, the chemistry doesn't matter.

11. What is the diameter of the wire? 14AWG wire has a conductor diameter of approx 1.63mm, plus insulation.

12. Is this genuine Amass? This is a generic high-quality connector compatible with Amass XT60.

13. Do you have the female version? Yes, check our store for the matching XT60 Female pigtail.

14. How flexible is the wire? Extremely flexible, much softer than standard PVC house wire.

15. Can I extend the wire length? Yes, by soldering additional 14AWG wire and using heat shrink, though a continuous run is always better.

16. Is it waterproof? The connector itself is not waterproof.

17. What happens if I plug it in backwards? The XT60 design is keyed (asymmetrical) to mechanically prevent reverse polarity connection.

18. Can I use this for solar panels? Yes, for low voltage, high current portable solar setups.

19. Does it come with heat shrink? The connector side is already insulated/shrunk. You may need heat shrink for your own connection at the other end.

20. Why use silicone over PVC? Silicone doesn't melt when your soldering iron touches it, making assembly much cleaner and safer.