Amass XT90H Female Connector with 10AWG High Temp Silicone Wire Pigtail - 15cm

Specifications

• Connector Type: Amass XT90H Female (Socket) - Battery Side

• Wire Gauge: 10AWG (Heavy Duty - 90A Rated)

• Wire Length: 15 cm

• Insulation: Soft Silicone (200°C Rated)

• Conductor: Tinned Copper

• Rated Current: 90A Continuous / 120A Peak

• Housing Material: Amass High-Temp Nylon + Snap-on Sheath

Key Applications & Projects

• Agri-Drones: Powering large 10L/16L spray drones running 12S voltage.

• E-Bikes & Skateboard: Main battery discharge lead for high-power 48V/60V/72V systems.

• Solar Power: High-current interconnects for portable solar generators.

Unlock New Capabilities (Project Evolution)

• Prerequisites: Building a high-power system (>60A).

• Feature Upgrade: Replacing standard XT60s with XT90s eliminates connector heating and voltage sag, giving your motors more punch and your system higher efficiency.

• Effort Level: Intermediate. Requires a high-power soldering iron (80W+) to solder the thick 10AWG wire to your PDB.

Virtual Technician & Wiring

• ⚠️ Soldering Tip: 10AWG wire sucks up a lot of heat. Use a broad chisel tip and high heat (400°C+) to solder the free end to your board quickly to avoid melting adjacent components.

• Polarity:

  • Flat Side: Positive (+)

  • Chamfered Side: Negative (-)

Accessories & Parts

What's Included:

• 1 x Amass XT90H Female Connector with 15cm 10AWG Silicone Wire

Required Alternatives:

• For ESC/Load Side: You need the Amass XT90H Male Pigtail.

• Spark Protection: For voltages above 6S (22V), consider using an XT90-S Anti-Spark connector on the ESC side to prevent the "pop" when plugging in.

Frequently Asked Questions (FAQ)

1. Is this for the battery? Yes, Female (Sockets) = Battery Side.

2. Is 10AWG really necessary? If you are running >60A, yes. 12AWG gets hot; 10AWG stays cool.

3. Will this fit a standard XT90? Yes, XT90H is fully compatible with standard XT90 and XT90-S.

4. Is the wire silicone? Yes, genuine high-strand silicone wire.

5. What is the "H" in XT90H? It stands for the plastic Housing (sheath) that covers the solder joints, replacing heat shrink.

6. Can I use this for 12S LiPos? Yes, rated for 500V+.

7. Is the connector Amass? Yes, 100% Genuine Amass.

8. What is the max burst current? ~120 Amps.

9. Is the length 15cm? Yes.

10. Is it waterproof? No.

11. Does it spark? This connector does NOT have the anti-spark resistor. (The XT90-S Male usually holds the resistor).

12. Can I use crimping? No, solder only.

13. Is the wire flexible? Yes, despite being thick, silicone insulation makes it flexible.

14. Can I use this for my scooter? Yes, perfect for 60V/72V scooter batteries.

15. Is polarity marked? Yes, on the housing.

16. Why is it expensive? 10AWG copper is expensive, and Amass connectors cost more than clones.

17. Can I cut the wire? Yes.

18. Will it melt? The nylon is heat resistant, but good soldering technique is required.

19. Do I need heat shrink? No, the "H" sheath covers the joint. You only need heat shrink for your board connection.

20. Is the soldering reliable? Yes, heavy-duty QC checked.