U.FL (IPEX) to TNC Female Bulkhead Pigtail - 15cm (Panel Mount Jack)

Specifications

• Connector A: U.FL (IPEX 1 / MHF1) Female

• Connector B: TNC Female Bulkhead (Standard Polarity)

• Pin Configuration: Female Socket (Hole)

• Thread Type: 7/16-28 UNEF (External Threads)

• Mounting Hole Size: Approx 12mm (15/32" or 7/16" depending on cut)

• Cable Type: 1.13mm Micro Coaxial

• Impedance: 50 Ohms

• Length: 15 cm

• Insulation: FEP (Fluorinated Ethylene Propylene)

Key Applications & Projects

• RTK GPS Base Stations: Exposing the antenna port for high-precision GNSS receivers (e.g., u-blox F9P/M8P).

• Avionics & Drones: Secure antenna mounting for long-range telemetry radios where vibration is a concern.

• Industrial Enclosures: Weather-resistant antenna mounting for agricultural monitoring nodes.

Virtual Technician & Wiring

• ⚠️ Polarity Check:

  • Standard TNC Female (This Cable): Has a Hole. Threads are on the Outside. Mates with TNC Male (Pin).

  • RP-TNC Female: Has a Pin. Often found on Cisco WiFi. This cable will NOT fit RP-TNC antennas.

  • Usage Rule: Look at your antenna connector. If it has a Solid Pin sticking out, this cable is the correct match.

Accessories & Parts

What's Included:

• 1 x U.FL (IPEX) to TNC Female Bulkhead Pigtail (15cm)

• 1 x Hex Nut

• 1 x Lock Washer

Compatible Upgrades:

• Antenna: High-Gain TNC GPS/GLONASS Antenna.

• Sealant: Use a rubber O-ring or silicone for waterproof outdoor mounting.

Frequently Asked Questions (FAQ)

1. What size hole do I need to drill? You need a hole approximately 11.5mm to 12mm in diameter.

2. Is this RP-TNC? No. This is Standard TNC. It has a hole in the center. RP-TNC has a pin.

3. Will this fit my Cisco WiFi antenna? Likely NO. Most Cisco antennas are RP-TNC (Male Pin). This jack requires a Male Pin on the antenna side, so check your antenna carefully. If your antenna has a hole, it is RP-TNC Male (Plug) and won't fit this.

4. What is the cable length? 15cm.

5. Does it come with the nut? Yes, Nut and Washer are included.

6. Is the IPEX connector compatible with M.2? No, M.2 cards use IPEX 4. This is IPEX 1.

7. Is the cable 1.13mm? Yes.

8. Can I use this for RTK GPS? Yes, TNC is the standard for survey-grade GPS antennas.

9. Is it waterproof? The connector itself is not IP-rated, but tightening it against a smooth enclosure wall provides a decent seal. Use an O-ring for better waterproofing.

10. What is the impedance? 50 Ohms.

11. Is the connector rotating? No, the Bulkhead is fixed to the panel. The antenna rotates to screw onto it.

12. Will this fit a Mini-PCIe card? Yes.

13. Why use TNC instead of SMA? TNC handles vibration much better and is physically stronger.

14. Is the contact gold plated? Yes, the internal socket is gold plated.

15. Can I use this for 900MHz Telemetry? Yes.

16. Does it fit through thick panels? It fits panels up to approx 4-5mm thick.

17. Is this compatible with BNC? No, BNC uses a twist-lock. TNC uses threads.

18. Can I extend it? Yes, with a TNC Male to Female extension cable.

19. What frequency does it support? DC to 11 GHz.

20. Is the washer a lock washer? Yes, usually a toothed star washer or split washer to prevent rotation.