Black ABS Enclosure Case for Raspberry Pi 5B with Active 5V Cooling Fan

FREQUENTLY ASKED QUESTIONS (FAQ)

1. Does this case include the Raspberry Pi computer? No. As stated in the disclaimer, this listing is only for the ABS plastic case, the fan, and the mounting hardware. You must provide your own Raspberry Pi 5B.

2. Will this case fit a Raspberry Pi 4 Model B? No. The Raspberry Pi 5 completely changed the layout of the USB ports, Ethernet port, and removed the audio jack. This case is strictly molded for the Pi 5.

3. What material is the case made from? It is made from high-quality, impact-resistant ABS (Acrylonitrile Butadiene Styrene) plastic.

4. What are the specifications of the included fan? The included fan is an SHCHV DC brushless fan rated for 5V and 0.20A.

5. Where do I plug the fan in? The Raspberry Pi 5 features a dedicated 4-pin JST fan header specifically for cooling fans. Alternatively, you can wire the red and black cables directly to the 5V and Ground pins on the GPIO header.

6. How do I assemble the case? The case is a simple 3-part design. Lay the Pi into the bottom base, snap the middle frame over it, screw the fan into the top lid, and snap the top lid onto the frame.

7. Do I need tools to assemble the case? The plastic case pieces snap together without tools. However, you will need a small Phillips-head screwdriver to attach the cooling fan to the top lid using the four included screws.

8. Can I access the GPIO pins with the case closed? The standard design encloses the top of the board to force air through the fan vents. To attach standard GPIO jumper wires or HATs, you will typically need to remove the top lid.

9. What is the small black square included in the kit? That is an adhesive thermal pad. It is used to transfer heat from the Pi's CPU to a heatsink (if you have one) or to help dissipate heat safely.

10. What are the four small clear dots for? Those are adhesive silicone rubber feet. You stick them to the four corners of the bottom base so your case won't slide around or scratch your desk.

11. Can I see the power LED through the case? The case is solid black ABS, but the design typically features a small micro-hole or relies on the side port gaps to let the status LED shine through.

12. Will the fan drain my power supply? The fan draws a maximum of 0.20 Amps (1 Watt) at 5V. As long as you are using the recommended 27W USB-C power supply for the Pi 5, the fan's power draw is completely negligible.

13. Is the fan loud? Small 5V fans do produce an audible hum at full speed. However, if plugged into the Pi 5's dedicated fan header, the Pi will automatically control the fan speed based on CPU temperature, keeping it very quiet during idle tasks.

14. Do I have to use the fan? No, you can leave the fan unplugged or uninstalled, but the Pi 5 runs very hot. It is highly recommended to use the active cooling fan to prevent your computer from slowing down (thermal throttling).

15. Can I use the official Raspberry Pi 5 Active Cooler with this case? Because this is a "Bigger Size" case, it has more internal clearance than standard slim cases. Depending on the exact dimensions, many low-profile active coolers can fit inside if you do not mount the included lid fan.

16. How do I access the MicroSD card? The bottom piece of the case features a slotted cutout perfectly aligned with the Pi 5's MicroSD card reader, allowing you to swap OS cards without opening the case.

17. Does the case block the WiFi or Bluetooth signal? No. ABS plastic is completely transparent to radio frequencies. Your WiFi and Bluetooth will work perfectly without signal degradation.

18. Can I mount a camera or display ribbon cable? Yes, there are thin slits integrated into the middle frame layer designed to allow the delicate ribbon cables for cameras and DSI displays to pass through.

19. How do I clean the case? You can wipe the ABS plastic down with a slightly damp microfiber cloth. Do not use harsh solvents like acetone, as they will melt the plastic.

20. Can I mount this case to a wall? The bottom base features two cross-shaped keyhole mounting slots. This allows you to easily slide the case onto two screws mounted in a wall or under a desk!